The packing is the most important part of the cooling tower, and its efficiency depends on the degree of full contact between the cooling water and the air in the packing. The company's filler temperature 50 ℃ ~ 68 ℃, aging resistance, excellent performance, UV resistance, long life. Its advantages are as follows:

1. Good performance and high cooling efficiency. The filler is of thin film type, and the protruding fine corrugations make the water contact surface larger. The filler is placed in 3~4 layers, and there is a redistribution process of hot water between layers.

2. The packing with good hydrophilicity and small ventilation resistance has good hydrophilicity and smooth surface, and the water absorption rate is less than 0.015, so that more water flow forms a thin film without splashing, so that water and air are more fully contacted and the surface disturbance of water and air is large when flowing. After the packing is assembled, the air inlet surface is a honeycomb-shaped deflector, which has a good uniform wind effect and improves and stabilizes the heat exchange intensity of water and gas. The wind inlet is inclined at an angle of 30 °, which effectively reduces the drift loss. A water collector designed according to the impact separation method is arranged at the end of the filler, so that the drift loss is effectively controlled within one hundred thousandth.

3. The series cooling tower core material is made of high quality PVC polyethylene sheet

It is made of plastic suction. Due to the use of trapezoidal wave filler, the heat dissipation area has a large growth coefficient, the water flow has good distribution performance on the plate surface, and the water and air flow through the plate surface has the advantages of large disturbance. The filler is not easy to deform, high temperature resistance, aging resistance, good flame retardant performance and small drag coefficient. Easy to install, easy to clean, easy to transport the heat dissipation filler using non-adhesive hanging type, easy to install, easy to clean, and successfully solved the adhesive filler due to suction fouling, weight and deformation, and after the deformation of the fouling is more serious, difficult to clean the problem. The filler has good flame retardant performance, and the flame retardant oxygen index index is 44.7.

4. The heat dissipation of the packing accounts for more than 85% of the total temperature drop in the cross-flow tower. The heat dissipation process of the cooling tower is mainly carried out on the plate surface of the heat dissipation filler. The water film on the surface of the filler slowly flows down. The innermost water film is high enthalpy wet air with a humidity of 100. Water molecules run from the high enthalpy area to the low enthalpy fresh air entering the tower, increasing the enthalpy value of the air coming out of the tower. As the concentration of water molecules decreases, the water molecules in the circulating hot water continuously evaporate from liquid to gaseous, thereby taking away the latent heat of vapor. According to the above principle, the advantages and disadvantages of the packing is the key to the refrigeration effect. Yuanxin brand cooling tower packing meets the requirements of the fourth generation packing in the world: large disturbance/three-dimensional deformation/accurate positioning; Small static pressure loss and small airflow negative force; Long water flow time (high 3000 ㎜); Large contact area and large area growth coefficient; Uniform distribution of water and air (honeycomb wind distribution device is provided at the air inlet, so that the tower will not have uneven wind distribution due to uneven film spacing, the uniform wind load makes the heat dissipation packing area of the tower effectively used. No deformation; No crushing; Good water quality; High strength; Low noise and low water drift; Long life; No moss is allowed to grow. Due to the three-dimensional characteristics of the honeycomb air inlet, most sunlight cannot enter the packing surface of the tower body, so it is difficult for moss to grow on the packing surface.

5. Square cooling tower packing adopts domestic original (commonly used abroad) suspended packing without bonding. As we all know, the surface of the packing crystallizes and precipitates due to evaporation of water in circulating water and increase of inorganic concentration, scaling occurs on the surface of the packing and the inner wall of the tower and the inner wall of the pipeline. The old continental packing is bonded and supported by a bracket. In use, it falls into a "vicious circle", that is, its weight becomes heavier after fouling, with the impact of water flow, "bending over" deformation occurs, and the front of the deformed filler is impacted by the water flow, which in turn makes the deformation more serious. This is an irreversible "vicious circle". When this cycle starts, the filler will soon break and collapse the bonding point due to pulling force. The suspended filler forms a virtuous circle of "dynamic balance". When the surface is fouled, the filler will maintain its original vertical shape due to its own weight, with the water flow erosion, the surface over the thickness of the scale off, the formation of dynamic balance, will not be damaged by the scale, improve the service life of the filler, square cross-flow cooling tower filler warranty for ten years.