News Center

Standard size of cross-flow cooling tower packing

The distance between the top of the cross-flow cooling tower filler and the lower end of the fan should be 1.2 times the diameter of the fan.

2019

09-03

Widespread application of cross-flow cooling tower packing

The choice of cooling tower filler depends first on its material. The recycled filler material is poor, and the raw material may be reused many times, so the sheet material is thicker and used for molding the filler. Most of the primary fillers are formed by suction molding, and the sheets are thin but of good quality. Weight is related to material and sheet distance.

2019

09-03

Brand cooling tower packing good quality

The filler is also called water spraying device, heat sink, etc. Its function is to form fine water droplets or thin water film as much as possible into the hot water, increase the contact area and contact time between water and air, and facilitate the heat exchange between water and air. Therefore, it is an important part of the cooling tower. Fillers are generally divided into: S wave filler, oblique staggered filler, stepped trapezoidal oblique wave filler, differential sine wave filler, point wave filler, hexagonal honeycomb filler, bidirectional wave filler, oblique folding wave filler, etc. Inferior filler has weak rigidity, poor bearing capacity, easy deformation and loose lodging, which directly leads to poor cooling effect or loss of cooling capacity.

2019

09-03

Service life of cooling tower packing

Cooling tower filler, this many aspects of the decision, air pollution, water quality, and is the annual water treatment, water treatment agent on the life of the filler also has an impact! However, the materials used by well-known cooling tower enterprises are good, and the service life is relatively high. There are also white transparent fillers (except PP high-temperature fillers) that are not UV-resistant, refractive, and the surface is too smooth. His service life will be shorter than others, and the cooling effect of relative cooling towers will be much worse than others.

2019

09-03

Fouling treatment method of cooling tower packing

The main material of the cooling tower filler is: PVC, which is a kind of plastic. Better quality cooling tower packing can be used directly after cleaning. If the quality of the filler itself is not good, or it is relatively thin, or even some of it is broken when touched, it is recommended to replace it with a new filler. The new filler is not expensive and saves a lot of trouble. Therefore, in the daily purchase of cooling tower packing process, we recommend the use of good quality packing.

2019

09-03

Shaping filler sheet

Shaped pieces of drenched filler shall be tightly packed with flat hard material to prevent permanent deformation due to poor packaging. Each package and roll of original sheet shall be marked with product name, specification, quantity, brand, batch number, manufacturer, production date, stacking mark, inspector code and inspection certificate, etc.

2017

09-06

The Importance of Cooling Tower Fillers

The packing is the most important part of the cooling tower, and its efficiency depends on the degree of full contact between the cooling water and the air in the packing. The company's filler temperature 50 ℃ ~ 68 ℃, aging resistance, excellent performance, UV resistance, long life.

2017

09-05

Sources of cooling tower packing

Granular filler: aluminum chips and aluminum powder, aluminum borate whiskers, alumina, anthracite, sodium antimonate, antimony trioxide, apatite, soot, attapulgite, barium metaborate, barium sulfate, barium titanate, bentonite, Bismuth oxide, boron oxide, calcium carbonate, calcium hydroxide, calcium sulfate, carbon black, ceramic microspheres, clay, diatomite, ferrite, feldspar, glass beads, gold, graphite, calcium silicate hydrate, kaolin, magnesium oxide, magnesium hydroxide, nickel hydroxide, molybdenum, pumice, frozen stone, rubber particles, sepiolite, silica, silica gel, silver powder, talc, titanium dioxide, zeolite, zinc borate, zinc sulfide. Fibers: aramid fibers, cellulose fibers, glass fibers, other fibers, etc.

2017

09-04

Cooling tower packing selection criteria

For a particular application, the optimal standard of filler filler is based on the desired properties of the composite material, but the following basic principles must be considered. 1. The filler must maintain its original structure during processing, and maintain inertness, insolubility, thermal stability, non-volatility, no catalytic activity and low adsorption. 2, the filler must be compatible with the substrate, non-corrosive. 3. Easy to handle, high bulk density, low moisture content, low dust, non-toxic. 4, must be easy to get, sufficient supply, moderate price, stable quality.

2017

09-01

The performance of cooling tower packing

Mainly depends on: ① has a larger specific surface area (m2/m3 filler layer); ② liquid in the filler surface has a good uniform distribution performance; ③ air flow can be evenly distributed in the filler layer; ④ seasoning has a larger porosity (m3/m3 filler layer). In addition, the choice of filler should also consider its mechanical strength, source, manufacture and price and other factors.

2017

08-31

< 123 >

Pursuit of excellence and customer foremost

Messages